urethane mounts

Biggs · 05-12-2006, 03:44 PM

where would you get this shore 90A urethane at, and hwo long does it take to dry? like a week?

Ovaltine Jenkins · 05-12-2006, 03:48 PM

you gotta get it online, and if you do it, the mounts should not be supporting the engine, they would need to be taken out and left somewhere to cure for at least a week.

Biggs · 05-12-2006, 04:18 PM

i can use this to like patch up mounts that are almost like broken right?

Ovaltine Jenkins · 05-12-2006, 04:23 PM

yeah, but you might as well just remove the old rubber and put in new urethane.

Biggs · 05-12-2006, 04:40 PM

if i were to remove the old rubber, how can i be certain that the hole of the screw is in the right place.

Ovaltine Jenkins · 05-12-2006, 04:52 PM

well, the metal sleeve is right in the middle, isn't it? Hold the sleeve in the middle, pour the urethane, hold the sleeve or make something to hold it in place, and that's it.

Biggs · 05-12-2006, 04:58 PM

do you know exactly where i can get this urethane stuff at? Might do my shifter bushing too

Ovaltine Jenkins · 05-12-2006, 05:09 PM

just google it, I looked for it a few months ago but forgot the sites.

05-12-2006, 06:04 PM

McMaster-Carr

aznsap · 05-12-2006, 07:46 PM

Shore A 80 urethane (part # 8644K11) purchased from www.mcmaster.com

http://www.cardomain.com/ride/352601/8

i did my 2 motor mounts and my tranny mount. i wish i had done my shifter bushing too but didn't think about it at the time.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ES motor mounts	Grzesiu	A33	12	03-28-2007 04:04 PM
any installers out there? LTB and Urethane Bushings	dko	A32	0	07-03-2006 03:02 PM
es motor mounts	mjk	A33	11	05-16-2006 12:38 AM

05-12-2006, 03:44 PM	#1
Biggs CNC Senior Member Join Date: Jan 2006 Location: Chicago, IL Age: 24 Posts: 1,808 Car: FD3S	where would you get this shore 90A urethane at, and hwo long does it take to dry? like a week?

05-12-2006, 03:48 PM	#2
Ovaltine Jenkins CNC Senior Member Join Date: Jan 2006 Location: C'ville, IL Posts: 3,106 Car: 96 5spd	you gotta get it online, and if you do it, the mounts should not be supporting the engine, they would need to be taken out and left somewhere to cure for at least a week.

05-12-2006, 04:18 PM	#3
Biggs CNC Senior Member Join Date: Jan 2006 Location: Chicago, IL Age: 24 Posts: 1,808 Car: FD3S	i can use this to like patch up mounts that are almost like broken right?

05-12-2006, 04:23 PM	#4
Ovaltine Jenkins CNC Senior Member Join Date: Jan 2006 Location: C'ville, IL Posts: 3,106 Car: 96 5spd	yeah, but you might as well just remove the old rubber and put in new urethane.

05-12-2006, 04:40 PM	#5
Biggs CNC Senior Member Join Date: Jan 2006 Location: Chicago, IL Age: 24 Posts: 1,808 Car: FD3S	if i were to remove the old rubber, how can i be certain that the hole of the screw is in the right place.

05-12-2006, 04:52 PM	#6
Ovaltine Jenkins CNC Senior Member Join Date: Jan 2006 Location: C'ville, IL Posts: 3,106 Car: 96 5spd	well, the metal sleeve is right in the middle, isn't it? Hold the sleeve in the middle, pour the urethane, hold the sleeve or make something to hold it in place, and that's it.

05-12-2006, 04:58 PM	#7
Biggs CNC Senior Member Join Date: Jan 2006 Location: Chicago, IL Age: 24 Posts: 1,808 Car: FD3S	do you know exactly where i can get this urethane stuff at? Might do my shifter bushing too

05-12-2006, 05:09 PM	#8
Ovaltine Jenkins CNC Senior Member Join Date: Jan 2006 Location: C'ville, IL Posts: 3,106 Car: 96 5spd	just google it, I looked for it a few months ago but forgot the sites.

05-12-2006, 07:46 PM	#10
aznsap Supporting Member Join Date: Mar 2006 Location: moline or chicago Posts: 385 Car: 95 white 5spd gle	Shore A 80 urethane (part # 8644K11) purchased from www.mcmaster.com http://www.cardomain.com/ride/352601/8 i did my 2 motor mounts and my tranny mount. i wish i had done my shifter bushing too but didn't think about it at the time.

05-12-2006, 06:04 PM	#9
Brian Guest Posts: n/a	McMaster-Carr